Skip to main content

Route Optimization Settings Explained

What each optimization setting on a route does: auto-optimization modes, start and end times, start and end points, and stop durations.

M
Written by Matt Panton

Route optimization means SMRT works out the quickest order to visit the day's stops, so you don't have to. This article explains each optimization setting on a route and when to use it.

Where to find these settings:Settings → Delivery → Delivery Routes → click the route. The settings are in the Real-Time Route Optimization section. Click Save when you're done.

Optimized or fixed?

Every route works one of two ways:

  • Optimized (Optimization Enabled): SMRT plans a new stop order every day. Customers don't have a permanent stop number.

  • Fixed (Optimization Disabled): each customer has a stop number, and the route always runs in that order. See How Stops Are Ordered on Your Routes.

The rest of the settings below only appear when Optimization Enabled is selected.

Route Auto-Optimization Mode

This decides whether SMRT plans the route by itself or waits for you.

  • Always auto optimize as route additions occur: SMRT plans the day automatically early each morning. Stops added later that day are fitted into the plan as they come in.

  • Stop optimizing upon manual optimization: SMRT also plans the day automatically early each morning and fits in new stops.

  • Trigger optimization manually: SMRT never plans the route by itself. You click Optimize on the Delivery screen when you're ready. Stops added after that show a map icon instead of a number until you optimize again.

Moving a stop by hand: if someone drags a stop to a new place on the Delivery screen, SMRT stops re-ordering that route for the rest of that day, so the change sticks. Clicking Optimize hands the day back to SMRT.

Start and end times

  • Start Time and End Time (near the top of the route page) are the route's working hours.

  • Strict Start Mode: when Enabled, the driver is never planned to leave before the route's start time. When Disabled, SMRT may start the driver a little earlier if that makes a better route.

  • Respect end time: when Enabled, the route must finish by its end time. Stops that don't fit are left unplanned. They show a map icon, and the Delivery screen shows a warning listing them. When Disabled, the route may run past its end time so every stop fits.

Start point and end point

By default, a route starts and finishes at the store it runs from.

  • Start point: tick Start somewhere other than (your store) and drag the marker on the map to where the driver begins the day. If a driver is already out on the road, SMRT plans from where they are now. (This doesn't apply when routes are optimized together.)

  • End point has three choices:

    • Return to (your store): the route ends back at the store. This is the default.

    • Finish at a specific point: drag the marker on the map to where the driver should finish.

    • Finish at the last stop: SMRT doesn't plan for the drive home. This lets it work from one side of the area to the other instead of looping back.

If you see Set latitude and longitude on (your store) before choosing a point on the map, your store's location needs to be filled in first.

How long each stop takes

  • Use customer stop average duration: when Enabled, SMRT uses how long each customer's last three stops took on average. If a customer has no history yet, it allows 5 minutes. This makes the plan more realistic.

  • Max duration per stop (minutes): shows when the setting above is on. It's the longest SMRT will allow for any one stop. The default is 30 minutes.

Optimize with other routes

This lets one route plan its stops together with other routes, so the stops are shared between several vans. It's only available on a Master route with no subroutes. See Optimize Several Routes Together for the full steps.

Optimizing a route yourself

  1. Open Delivery from the home screen.

  2. Pick the day and select the route.

  3. Click Optimize.

You can optimize today or a future day, but not a day that has already passed. Running it again on a day that was already optimized changes the stop order, so avoid this once the driver has loaded the van.

Good to know

  • A route can have up to 250 stops per day for optimization. If you go over, you'll see Please make sure there are no more than 250 deliveries per day. Split the work across more routes.

  • A subroute always follows its master route. Its settings show Route optimization is handled by and the master route's name.

  • Changes to these settings take effect the next time the route is optimized.

Did this answer your question?